Překlad/translate
.

Nákupní košík

Košík je prázdný

Vyhledávání

Spektrální / obvodové analyzátory
Úvodní strana / Produkty / Měřicí přístroje / Spektrální / obvodové analyzátory / RSA603 a RSA607 Real Time Spectrum Analyzers
zpět

RSA603 a RSA607 Real Time Spectrum Analyzers

RSA603 a RSA607   USB spektrální analyzátor
  • USB spektrální analyzátor
  • 9 kHz až 3 GHz nebo 9 kHz-7,5 GHz
  • 40 MHz real-time bandwidth
  • v dodávce základní verze SignalVu software
  • záruka: 3 roky

 

Výrobce: Tektronix
Kód: RSA603 & RSA607


Cena na vyžádání

Doba doručení: na dotaz

Poptat

 

PARAMETRY A SPECIFIKACE:

Frequency range
RSA603A 9 kHz to 3 GHz
RSA607A 9 kHz to 7.5 GHz
Frequency marker readout accuracy

±(RE × MF + 0.001 × Span) Hz

RE: Reference Frequency Error

MF: Marker Frequency [Hz]

Reference frequency accuracy
Initial accuracy at Cal (30 min warm-up) ±1 x 10-6
First year aging, typical ±1 x 10-6 (1 year)
Cumulative error (Initial accuracy + temperature + aging), typical 3 x 10-6 (1 year)
Temperature drift ±0.9 x 10-6 (-10 to 60 °C)
External reference input BNC connector, 50 Ω nominal
External reference input frequency

Every 1 MHz from 1 to 20 MHz plus the following: 1.2288 MHz, 2.048 MHz, 2.4576 MHz, 4.8 MHz, 4.9152 MHz, 9.8304 MHz, 13 MHz, and 19.6608 MHz.

The spurious level on the input signal must be less than -80 dBc within 100 kHz offset to avoid on-screen spurious.

External reference input range ± 5 ppm
External reference input level -10 to +10 dBm
GNSS
Accuracy, when locked to GNSS1 ±0.025 ppm2
GNSS Trained Accuracy, when GNSS antenna is disconnected3, 4

±0.025 ppm5

±0.08 ppm6

RF input
RF Input Impedance 50 Ω
RF VSWR (RF Attn = 20 dB), typical

< 1.2 (10 MHz to 3 GHz)

< 1.5 (>3 GHz to 7.5 GHz)

RF VSWR preamp ON, typical

< 1.5 (10 MHz to 6 GHz, RF ATT=10 dB, preamp on)

< 1.7 (> 6 GHz to 7.5 GHz, RF ATT=10 dB, preamp on)

Maximum RF input level
Maximum DC voltage ±40 V (RF input)
Maximum safe input power

+33 dBm (RF input, 10 MHz to 7.5 GHz, RF Attn ≥ 20 dB)

+13 dBm (RF input, 9 kHz to 10 MHz)

+20 dBm (RF input, RF Attn < 20 dB)

Maximum safe input power (Preamp On)

+33 dBm (RF input, 10 MHz to 7.5 GHz, RF Attn ≥ 20 dB)

+13 dBm (RF input, 9 kHz to 10 MHz)

Maximum measurable input power

+30 dBm (RF input, ≥10 MHz to Fmax, RF ATT Auto)

+20 dBm (RF input, <10 MHz, RF ATT Auto)

Input RF attenuator 0 dB to 51 dB (1 dB step)
Amplitude and RF flatness
Reference level setting range -170 dBm to +40 dBm, 0.1 dB step, (Standard RF input)

 

1Tested using GPS system.

2For use to a stability of ±0.025ppm, the unit should be powered on continuously for 2 to 5 days after initial unpacking.

3Tested using GPS system.

4For 24 hours continuous operation within temperature limits (see footnotes 5 and 6) after GNSS training. Refer to cumulative error specification if operating in GNSS trained mode beyond 24 hours since last training.

5For less than 3 °C ambient temperature change after training.

6For less than 10 °C ambient temperature change after training.

SOUBORY KE STAŽENÍ & ODKAZY:

.